Mounting A Tub
Mounting A Tub
Blog Article
We've noticed this article about A Step-by-Step Guide to Installing a Bathtub listed below on the internet and decided it made sense to relate it with you in this article.
Installing a tub isn't precisely brain surgery, however it does call for strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old tub with a new one is likewise a reasonably tough task. If the old bathtub is conveniently obtainable, the task can relocate easily; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub as well as embeded in the brand-new one. Make certain you have qualified yourself for the job and are comfortable attempting it. Rather than working with a service provider to take control of a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Chances are you may require a specialist plumber to make tube links.
This post will help you install a brand-new bath tub in your shower room if you have actually already bought a brand-new tub and don't require to alter the arrangement of your previous water pipelines.
Your tools and material list must make up the following:
Planning for the Installation
To start with, the sustaining framework supplied with the bathroom ought to be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the tap features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps system to prevent pressure on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to now be ready to be fitted in its last placement.
Removing Old Taps
If you require to replace old taps with new ones as a part of your setup, then the first thing you ought to do is separate the water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the limited access that is commonly the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the staying water that will certainly originate from the pipes. When the supply pipes have actually been removed, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. When the faucets have been eliminated, the holes in the bath/basin will need to be cleansed of any type of old securing compound.
Prior to moving on to fit the new faucets, compare the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are valuable in uniformly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as readjusting the feet on the bath tub until the spirit level reads level.
To set up faucets, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Turn on the water system as well as examine all joints and also brand-new pipework for leakages and also tighten them if essential. Load the tub and likewise check the overflow outlet and also the regular electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait till the tub has been used at least when as this will settle it right into its last setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washers remain in location between the faucet and also the sink. Protect the tap in position with the producer provided backnut. As soon as the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the tap ends initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, causing the water to pass through the wall in between the bath as well as the tiling, leading to issues with wetness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Remember to always load the bathtub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealer can fracture fairly early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is suggested to fit the tiles utilizing waterproof or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that review about How to Install a Bathtub Yourself when doing a lookup on the internet. Sharing is good. Helping people is fun. I love reading our article about Tools You Need to Install a New Bathtub .
This Post
Report this page